LC and MC not showing after CAMM install
Article ID: 200186
Updated On:
Products
Issue/Introduction
lc and mc are not showing up in page after CAMM install in lab
i get a pop up asking for some environmental settings.
See screen shot.
===============================================================================
Choose Install Folder
---------------------
Where would you like to install?
Default Install Folder: /opt/CA/CAMM
ENTER AN ABSOLUTE PATH, OR PRESS <ENTER> TO ACCEPT THE DEFAULT
:
===============================================================================
Choose Install Set
------------------
Please choose the Install Set to be installed by this installer.
->1- Typical
2- Upgrade
ENTER THE NUMBER FOR THE INSTALL SET, OR PRESS <ENTER> TO ACCEPT THE DEFAULT
:
===============================================================================
Choose Product Features
-----------------------
Please choose the Features to be installed by this installer.
->1- Multi Controller
2- Local Controller
ENTER A COMMA-SEPARATED LIST OF NUMBERS REPRESENTING THE DESIRED CHOICES, OR
PRESS <ENTER> TO ACCEPT THE DEFAULT: 2
===============================================================================
User Data
---------
Foundation Configuration
User ID: (Default: root):
GE Port: (Default: 29560):
===============================================================================
Get User Input
--------------
Local Controller Configuration:
The LC port is fixed to 29598:
LC IP: (Default: 127.0.0.1): 172.31.17.109
Failover Threshold: (Default: 600):
The MC-primary IP: : 172.31.17.110
The MC-secondary IP: : 172.31.17.110
===============================================================================
Overwrite existing file
-----------------------
All existing installed files will be overwritten. This will not affect any
files or folders created after installation.
PRESS <ENTER> TO CONTINUE:
===============================================================================
Pre-Installation Summary
------------------------
Please Review the Following Before Continuing:
Product Name:
DX NetOps MM
Install Folder:
/opt/CA/CAMM
Install Set:
Typical
Product Features:
Local Controller
PRESS <ENTER> TO CONTINUE:
===============================================================================
Please Wait
-----------
Stopping DX NetOps Mediation Manager...
===============================================================================
Installing...
-------------
[==================|==================|==================|==================]
[------------------|------------------|------------------|------------------]
===============================================================================
Installation Complete
---------------------
Congratulations. DX NetOps MM has been successfully installed to:
/opt/CA/CAMMPRESS <ENTER> TO EXIT THE INSTALLER
===============================================================================
Please Wait
-----------Starting DX NetOps Mediation Manager...
next is the MC
Choose Install Folder
---------------------
Where would you like to install?
Default Install Folder: /opt/CA/CAMM
ENTER AN ABSOLUTE PATH, OR PRESS <ENTER> TO ACCEPT THE DEFAULT
:
===============================================================================
Choose Install Set
------------------
Please choose the Install Set to be installed by this installer.
->1- Typical
2- Upgrade
ENTER THE NUMBER FOR THE INSTALL SET, OR PRESS <ENTER> TO ACCEPT THE DEFAULT
:
===============================================================================
Choose Product Features
-----------------------
Please choose the Features to be installed by this installer.
->1- Multi Controller
2- Local Controller
ENTER A COMMA-SEPARATED LIST OF NUMBERS REPRESENTING THE DESIRED CHOICES, OR
PRESS <ENTER> TO ACCEPT THE DEFAULT:
===============================================================================
User Data
---------
Foundation Configuration
User ID: (Default: root):
GE Port: (Default: 29560):
===============================================================================
Get User Input
--------------
Multi Controller Configuration:
Install primary MC or secondary MC?
->1- Primary
2- Secondary
ENTER THE NUMBER FOR YOUR CHOICE, OR PRESS <ENTER> TO ACCEPT THE DEFAULT:
===============================================================================
Get User Input
--------------
Multi Controller Configuration:
The MC port is fixed to 29599
MC IP: (Default: 127.0.0.1): 172.31.17.110
Failover Threshold: (Default: 600):
===============================================================================
Get User Input
--------------
Multi Controller Configuration:
Will the other MC exist in the Cluster?
1- Yes
->2- No
ENTER THE NUMBER FOR YOUR CHOICE, OR PRESS <ENTER> TO ACCEPT THE DEFAULT:
===============================================================================
Get User Input
--------------
Web Authentication Configuration
User: admin
Password: (Default: camm):
Web Port: (Default: 8880):
===============================================================================
Overwrite existing file
-----------------------
All existing installed files will be overwritten. This will not affect any
files or folders created after installation.
PRESS <ENTER> TO CONTINUE:
===============================================================================
Pre-Installation Summary
------------------------
Please Review the Following Before Continuing:
Product Name:
DX NetOps MM
Install Folder:
/opt/CA/CAMM
Install Set:
Typical
Product Features:
Multi Controller
PRESS <ENTER> TO CONTINUE:
===============================================================================
Please Wait
-----------
Stopping DX NetOps Mediation Manager...
===============================================================================
Installing...
-------------
[==================|==================|==================|==================]
[------------------|------------------|------------------|------------------]
===============================================================================
Installation Complete
---------------------
Congratulations. DX NetOps MM has been successfully installed to:
/opt/CA/CAMM
PRESS <ENTER> TO EXIT THE INSTALLER:
===============================================================================
Please Wait
-----------
Starting DX NetOps Mediation Manager...
Environment
Release : 20.2
Component : IM Reporting / Admin / Configuration
Resolution
Reinstall using the IP of the system instead of 127.0.0.1
Feedback
