Answer
List of the RDeploy (RapiDeploy) command-line switches:
-align:X | Set partition alignment: X={cyl|track} |
-bsl:N | Set broadcast speed limit to N MBits/sec |
-cmdline | Show the command line parameters in text mode |
-cfgfile:{NAME.EN_US} | Set the configuration filename (default is lastrun.cfg) |
-cX | Set compression type: X={off|size|balanced|speed} |
-dpos{1-2} | Specify the desired disk position if a disk will be removed after imaging |
-dsconfig:{NAME.EN_US} | Specify the Deployment Solution config file to be copied after restoring an image |
-dsstatus:{N.N.N.N:P} | Specify the IP and port to use for communication with Deployment Solution |
-dN[,N...][:N[,N...] | Specify the disks to process (for example, -d1 or -d1:2 (disk 1 to disk 2) or -d1,2 (Linux: LVM or RAID on disks 1 and 2 | DOS/WinPE: RAID on disks 1 and 2) |
-forcegui | Force the GUI wizard to appear even if it doesn't have to |
-forceoem | Force the OEM partition to be restored even if it exists on the destination |
-forcebf | Force boot fixup in cases where it does not normally occur |
-forcebw | Force the BW partition to be restored even if it exists on the destination |
-frm:{NAME.EN_US} | Specify files to be copied to the boot volume after restoring an image |
-f{NAME.EN_US} | Specify the image name |
-grubdir:{DIR.EN_US} | Specify the directory where the GRUB boot files are located |
-h | Show command line help |
-help | Show command line help |
-? | Show command line help |
-ip:{N.N.N.N:P} | Set the multicast IP address and port. |
-iosize:N | Set the size (in KBytes) of reads and writes to the image file (4-64k) If >32 and using DOS, you must set DOS32A=DOSBUF:n in the DOS environment |
-i{ID.EN_US} | Set the multicast session ID |
-i:{20-25} | Set the VGA screen mode (for example, 23=640x480x16) |
-kap |
Keep all existing partitions during download |
-kprs | Keep the existing recovery partition during download |
-kp{1-31} | Keep an existing partition during download |
-logo:{NAME.EN_US} | Specify a path to a progress dialog logo bitmap (PCX in dos, BMP in windows) |
-makeimx | Create an image index file (.imx) to reduce media swapping |
-mcastspeed:{SPEED.EN_US} | Set multicast speed. Range: 1 or greater. 1 = Deployment Solution 6.5 and previous speed, 5 = Deployment Solution 6.8 default. |
-mcint:{N.N.N.N} | Specify the interface for multicasting. (can be DEFAULT) |
-mclient | Operate in client mode |
-mconv | Convert .img to .exe |
-mdb | Download and multicast an image |
-mdd | Copy one disk to another disk |
-mig:{NAME.EN_US} | Specify migration file. Prompts before overwriting the disk. |
-mmm | Operate in multicast master mode |
-mub | Upload and multicast an image |
-mb | Multicast only |
-md | Download (restore) an image |
-mu | Upload (create) an image |
-nospacecheck | Don't check for available space on the volume where the image is being created |
-noprompt | Prevent any need for user interaction, for example, clicking OK after an error occurs |
-nocancel | Don't allow the user to cancel the imaging task |
-nooem | Make the destination end up with no OEM partition |
-nors | Make the destination end up with no Recovery Solution partition |
-nobw | Make the destination end up with no BW partition |
-nt64k | Force FAT16 to use 64k clusters (NT systems only) |
-n | Process the sources but not the destinations (null destination) |
-postconfig | Do post configuration from within RapiDeploy |
-password:{PWD.EN_US} | Specify the image password |
-poem | Image the oem partition unless it already exists (see -forceoem) |
-prs | Image the recovery partition |
-pb | Image the BootWorks partition unless it already exists (see -forcebw) |
-p{1-31} | Select the partitions to process (can be repeated, e.g. -p1 -p2, and so on) |
-raid:N | Specify the software RAID level |
-raw | Treat all partitions as raw |
-rescan | Tell the operating system to reread the partition table after imaging |
-restoresig | Restore the MBR disk signature during download |
-rscs:{NAME.EN_US} | Make a recovery solution checksum file during upload |
-splash:{NAME.EN_US} | Specify a path to a splash screen bitmap (PCX in dos, BMP in windows) |
-split:N | Split the image at N megabytes during upload |
-span | Prompt for media between image segments (use with -split) |
-szX[:Y] | Resize partitions: -sze, -szf, -szX:e, -szX:eY, -szX:f, -szX:Nm, -szX:Np (X,Y=slot, e=existing, f=fixed, m=MBytes, p=percentage) |
-sN | Send to N clients |
-threshold:N | Set the minimum number of clients needed to multicast |
-throttle:N | Set the maximum megabits per second (Mbps) bandwidth RapiDeploy can use. |
-text | Run in text mode instead of GUI mode |
-ve:{31-34} | Set VESA screen mode (e.g. 31=640x480x256) |
-ver | Display version information and exit |
-wN | Set the timeout (in minutes) for autonegotiation and client connecting |
-x | Make the image self-extracting during upload |