Database Analyzer U0500 abend module RALMBLD fatal error encountered
Article ID: 131970
Updated On:
Products
CA Database Analyzer for DB2 for z/OS
CA Fast Unload for DB2 for z/OS
CA Fast Check for DB2 for z/OS
CA Fast Index for DB2 for z/OS
CA Fast Load for DB2 for z/OS
CA Rapid Reorg for DB2 for z/OS
Issue/Introduction
CA Database Analyzer for Db2 for z/OS (PDA) Extract execution is abending with the following:
USER COMPLETION CODE=0500
PSW AT TIME OF ERROR 078D1000 9BC5A24C ILC 2 INTC 0D
ACTIVE MODULE ADDRESS=00000000_1BC58000 OFFSET=0000224C
NAME=RALMBLD
DATA AT PSW 1BC5A246 - 00181610 0A0DD603 BA54BA54
AR/GR 0: 001FFFFF/80000000 1: 00000000/800001F4
2: 00000000/00000069 3: 00000000/1BC10C10
4: 00000000/1BC01630 5: 00000000/00000000
6: 00000000/0001D0D4 7: 00000000/00010EA0
8: 00000000/00000000 9: 00000000/1BC10DD8
A: 00000000/9BC5B008 B: 00000000/9BC5A008
C: 00000000/9BC59008 D: 00000000/9BC58008
E: 00000000/9BC5A208 F: 00000000/00000004
IEF450I DBBQT8PL UTIL1 STEP01 - ABEND=S000 U0500 REASON=00000000
> PDA PROFILE Fatal Abend option was set to YES. Entering debugging mode. <
Extracting EXTRACT Procedure - xxx.yyyyyyyy
No objects defined for the Extract Procedure. If it was created outside of the supported user interface then unpredictable results may occur. RC=4 Module: RALCBPB, Return code: 004, Reason code: 001
Execution stopped - fatal error encounter - Reason Code 105
USER COMPLETION CODE=0500
PSW AT TIME OF ERROR 078D1000 9BC5A24C ILC 2 INTC 0D
ACTIVE MODULE ADDRESS=00000000_1BC58000 OFFSET=0000224C
NAME=RALMBLD
DATA AT PSW 1BC5A246 - 00181610 0A0DD603 BA54BA54
AR/GR 0: 001FFFFF/80000000 1: 00000000/800001F4
2: 00000000/00000069 3: 00000000/1BC10C10
4: 00000000/1BC01630 5: 00000000/00000000
6: 00000000/0001D0D4 7: 00000000/00010EA0
8: 00000000/00000000 9: 00000000/1BC10DD8
A: 00000000/9BC5B008 B: 00000000/9BC5A008
C: 00000000/9BC59008 D: 00000000/9BC58008
E: 00000000/9BC5A208 F: 00000000/00000004
IEF450I DBBQT8PL UTIL1 STEP01 - ABEND=S000 U0500 REASON=00000000
> PDA PROFILE Fatal Abend option was set to YES. Entering debugging mode. <
Extracting EXTRACT Procedure - xxx.yyyyyyyy
No objects defined for the Extract Procedure. If it was created outside of the supported user interface then unpredictable results may occur. RC=4 Module: RALCBPB, Return code: 004, Reason code: 001
Execution stopped - fatal error encounter - Reason Code 105
Environment
Release:
Component: PDA
Component: PDA
Resolution
The presence of the following mesage is related to the U0500 abend in RALMBLD:
> PDA PROFILE Fatal Abend option was set to YES. Entering debugging mode. <
The proven way to correct this would be to utilize the PDA panels to regenerate the control cards with the PDA Profile option set to Fatal Abend ==> NO.
Steps:
1. Go into Database Analyzer option P User Profile and verify that Fatal Abend ==> NO is specified.
2. Go into Database Analyzer option EP and use the (S)ubmit line command to generate the JCL for the Extract Procedure in question.
> PDA PROFILE Fatal Abend option was set to YES. Entering debugging mode. <
The proven way to correct this would be to utilize the PDA panels to regenerate the control cards with the PDA Profile option set to Fatal Abend ==> NO.
Steps:
1. Go into Database Analyzer option P User Profile and verify that Fatal Abend ==> NO is specified.
2. Go into Database Analyzer option EP and use the (S)ubmit line command to generate the JCL for the Extract Procedure in question.
Feedback
Powered by
