Where does the CA DB MGT bind job ssid002 grab the DS names from?
Article ID: 126348
Updated On:
Products
CA RC/Migrator
CA Endevor SCM Interface
DB2 Administration
CA RC Compare for DB2 for z/OS
CA RC Extract for DB2 for z/OS
CA RC/Query
CA RC Secure for DB2 for z/OS
CA RC Update for DB2 for z/OS
CA Database Analyzer for DB2 for z/OS
CA Fast Unload for DB2 for z/OS
CA Fast Check for DB2 for z/OS
CA Fast Index for DB2 for z/OS
CA Fast Load for DB2 for z/OS
CA Rapid Reorg for DB2 for z/OS
Issue/Introduction
For the following CA DB MGT bind job:
//ISPMLIB DD DISP=SHR,DSN=TESTDB2.CA.SANDBOX.R19.CDBAMSG0
// DD DISP=SHR,DSN=ISPF.UPS.UPSMLIB
// DD DISP=SHR,DSN=ISPF.DB2.UPSMLIB
//ISPPLIB DD DISP=SHR,DSN=TESTDB2.CA.SANDBOX.R19.CDBAPNL0
// DD DISP=SHR,DSN=ISPF.DTWO.UPSPLIB
// DD DISP=SHR,DSN=SYS2.ISPF.ISPPLIB
// DD DISP=SHR,DSN=ISPF.DB2.UPSPLIB
//ISPSLIB DD DISP=SHR,DSN=TESTDB2.CA.SANDBOX.R19.CDBASKL0
// DD DISP=SHR,DSN=ISPF.DB2.UPSSLIB
//ISPTLIB DD DISP=SHR,DSN=ISPF.DTWO.UPSTLIB
// DD DISP=SHR,DSN=SYS2.ISPF.ISPTLIB
// DD DISP=SHR,DSN=ISPF.DB2.UPSTLIB
//ISPPROF DD DISP=(NEW,DELETE,DELETE),
// UNIT=SYSDA,SPACE=(TRK,(1,1,5)),
// DCB=(LRECL=80,RECFM=FB,BLKSIZE=6160,DSORG=PO)
//ISPLOG DD SYSOUT=*,DCB=(RECFM=VA,LRECL=125,BLKSIZE=129)
//ISPWRK1 DD DISP=(NEW,DELETE,DELETE),
// UNIT=SYSDA,SPACE=(TRK,(90,15)),
// DCB=(RECFM=FB,LRECL=256,BLKSIZE=2560)
//ISPFILE DD DISP=(MOD,PASS),DSN=&&CNTL,
// UNIT=SYSDA,SPACE=(32000,(90,60)),
// DCB=(RECFM=FB,LRECL=80)
where does it grab the DS names from?
//ISPMLIB DD DISP=SHR,DSN=TESTDB2.CA.SANDBOX.R19.CDBAMSG0
// DD DISP=SHR,DSN=ISPF.UPS.UPSMLIB
// DD DISP=SHR,DSN=ISPF.DB2.UPSMLIB
//ISPPLIB DD DISP=SHR,DSN=TESTDB2.CA.SANDBOX.R19.CDBAPNL0
// DD DISP=SHR,DSN=ISPF.DTWO.UPSPLIB
// DD DISP=SHR,DSN=SYS2.ISPF.ISPPLIB
// DD DISP=SHR,DSN=ISPF.DB2.UPSPLIB
//ISPSLIB DD DISP=SHR,DSN=TESTDB2.CA.SANDBOX.R19.CDBASKL0
// DD DISP=SHR,DSN=ISPF.DB2.UPSSLIB
//ISPTLIB DD DISP=SHR,DSN=ISPF.DTWO.UPSTLIB
// DD DISP=SHR,DSN=SYS2.ISPF.ISPTLIB
// DD DISP=SHR,DSN=ISPF.DB2.UPSTLIB
//ISPPROF DD DISP=(NEW,DELETE,DELETE),
// UNIT=SYSDA,SPACE=(TRK,(1,1,5)),
// DCB=(LRECL=80,RECFM=FB,BLKSIZE=6160,DSORG=PO)
//ISPLOG DD SYSOUT=*,DCB=(RECFM=VA,LRECL=125,BLKSIZE=129)
//ISPWRK1 DD DISP=(NEW,DELETE,DELETE),
// UNIT=SYSDA,SPACE=(TRK,(90,15)),
// DCB=(RECFM=FB,LRECL=256,BLKSIZE=2560)
//ISPFILE DD DISP=(MOD,PASS),DSN=&&CNTL,
// UNIT=SYSDA,SPACE=(32000,(90,60)),
// DCB=(RECFM=FB,LRECL=80)
where does it grab the DS names from?
Environment
Release:
Component: COMDB2
Component: COMDB2
Resolution
The ISPF datasets allocated in the CA DB2 tools bind JCL is read from the ISPFxx member in hlq.CDBAPARM. Check the ISPFxx member where xx = is the suffix being used.
Feedback
Yes
No
Powered by
