Ports used by Automation Point

Products

• Automation Point

Issue/Introduction

Automation Point needs to communicate with other products, devices.
This is done by using the TCPIP IP address, or TCPIP hostname.. However also via specific ports sometimes.
These ports are sometimes protected by a proxy or firewall.
 
What ports does AP use?
Can they be modified?
And if so, where can they be modified?

Environment

 Component: ATMXC

Resolution

For the new Automation Point r11.x server install, here some information on the ports used by AP.
                                                                    
The ports AP uses depends on the services you install :            
                                                                    
23      Automation Point - Telnet Session                
389     Automation Point - NM web Security Options      : Changed via AP Config Mngr, Expert, Notification, Notification Manager, NM Security
444     Automation Point - Simple Network Paging Protocol (SNPP)                
1202    Automation Point - CCI-PC (unencrypted)         : Changed via AP Config Mngr, Expert, Automation, Events Interface, OPS/MVS EMA, CCI Settings
1203    Automation Point - CCI-PC (encrypted)           : Changed via AP Config Mngr, Expert, Automation, Events Interface, OPS/MVS EMA, CCI Settings
1721    Automation Point - CCI-dist (encrypted)         : Changed via AP Config Mngr, Expert, Automation, Events Interface, OPS/MVS EMA, CCI Settings
2000    Automation Point - PPQs - configurable          : Changed via AP Config Mngr, Expert, Infrastructure, PPQ
4099    Automation Point - NM website  
5099    Automation Point - NM Web Gateway               : Changed via AP Config Mngr, Expert, Notification, Notification Manager, NM Website  
5500    Automation Point - Remote Viewing               : Changed via AP Config Mngr, Expert, Automation, Remote Viewing
5501    Automation Point - Unicenter Security for AP Sessions     
5700    Automation Point - Netspeak - configurable      : Changed via AP Config Mngr, Expert, Automation, AP Desktop Settings
7000    Automation Point - CCI-dist (unencrypted)       : Changed via AP Config Mngr, Expert, Automation, Events Interface, OPS/MVS EMA, CCI Settings
7000-7004 AP to NSM 
8443    Automation Point - Tomcat for TLS 
9803    AP Web services - notification                  : Changed via AP Config Mngr, Expert, Infrastructure, Web Services, Automation
9804    AP Web services - notification                  : Changed via AP Config Mngr, Expert, Infrastructure, Web Services, Notification
                                                                            
All the ports are TCP.
And the HMC and SNMP ports are both UDP and TCP ports.          
                                                                            
AP can use TN3270 :                                                         
                                                                            
AP uses a communication server that supports TN3270 (such as OSA-Integrated Console Controller (OSA-ICC) or IBM 2074 Console Controller) 
to host either operating consoles or VTAM applications using TN3270E connections through IBM 3278/3279 model 2,3,4, or 5 display terminals.      
                                                                            
And for TN5250 :                                                            
                                                                            
For IBM iSeries connections, Automation Point supports the 5292 terminal type only. This provides a 24x80 screen size.                               
                 
If you want to use the HAF interface to monitor HMC messages, AP uses these specific ports :
  151
  152
  161
  162
 3151
 3152
 3161
 3162
10151
10152
10161
10162
**** CMOS Processors

Default port for the NM SQL access is 1433.
Configurable since AP 11.4  

***
MS SQL and Tomcat ports are defaults specified by their vendors and can be subject of changes by them..                         

Additional Information

Until Automation Point release 11.6 these ports are also used:

6200    Automation Point - WebMV                        : Changed via AP Config Mngr, Expert, Automation, Web Msg Viewer, Advanced
6205    Automation Point - WebMV                        : Changed via AP Config Mngr, Expert, Automation, Web Msg Viewer, Advanced
6300    Automation Point - WebMV                        : Changed via AP Config Mngr, Expert, Automation, Web Msg Viewer, Advanced

With Automation Point release 11.7 they are not used anymore. The WebMV (Web Message Viewer) of Automation Point was replaced by the new Console Manager, which is using the ports 9803 and 9804.