Multiple S0E0 abends ZOS Agent
Article ID: 102372
Updated On:
Products
CA Automic Workload Automation - Automation Engine
AUTOMIC WORKLOAD AUTOMATION
Issue/Introduction
-The system message S0E0 Reason 28
Reserved bit positions in an access list entry token (ALET) were nonzero
-The offset where the program UCXJM25 aborted
PSW AT TIME OF ERROR 078C4400 800C1526 ILC 6 INTC 28
ACTIVE LOAD MODULE ADDRESS=00007000 OFFSET=000BA526
NAME=UCXJM25
DATA AT PSW 000C1520 - D207B030 41685850 41041F66
AR/GR 0: 00000000/00000000 1: 00000000/00006278
2: FFFFFFFF/00000433 3: FFFFFFFF/000004FA
4: 00620003/007F509C 5: 00620003/00000000
6: 00620003/59CD10C7 7: FFFFFFFF/00F18700
8: FFFFFFFF/03D9A000 9: FFFFFFFF/0000628C
A: FFFFFFFF/00006248 B: FFFFFFFF/3B682AB8
C: 00000000/000C1238 D: 00000000/3B682B00
E: 00000000/00006288 F: 00000000/00000000
END OF SYMPTOM DUMP
--
INTERRUPT OCCURRED AT ADDRESS 800C1520
LAST KNOWN I/O OR CALL OCCURRED AT ADDRESS 00B3B0F0 AT OFFSET +0000F0 IN MODULE CASESSIS
THE Z/OS BREAKING EVENT ADDRESS IS 00000000 01611912 IN UNKNOWN PROGRAM
--
There may be an issue when trying to write within the CAIPRINT repository, please check the following to confirm:
https://support.ca.com/us/knowledge-base-articles.TEC1754252.html
The system abend of the started tasks is most probably a side effect (OEO reason 28) — this may not fix the issue.
3. ACTUAL: The Agent will activate the extended console, it ACTIVATES an extended console, it say successful, but a second later, when the Agent “inactivates” the event console the agent dies.
The OS390 agent is using access registers without initializing them. We run with a list for DIAG traps successed by IBM to catch coding errors and need this corrected so we can pass out this agent to our systems.
EXPECTED: The Agent stays active
This console is only open if the 'defultJobClass' is not set wihin the INIfile of the agent.
Just set within the '(WLM)' section this parameter:
f.ex.:
(WLM)
defultJobClass=C
If this is set the function is scipped ($d intrdr,c) – this did not resolve the issue.
Reserved bit positions in an access list entry token (ALET) were nonzero
-The offset where the program UCXJM25 aborted
PSW AT TIME OF ERROR 078C4400 800C1526 ILC 6 INTC 28
ACTIVE LOAD MODULE ADDRESS=00007000 OFFSET=000BA526
NAME=UCXJM25
DATA AT PSW 000C1520 - D207B030 41685850 41041F66
AR/GR 0: 00000000/00000000 1: 00000000/00006278
2: FFFFFFFF/00000433 3: FFFFFFFF/000004FA
4: 00620003/007F509C 5: 00620003/00000000
6: 00620003/59CD10C7 7: FFFFFFFF/00F18700
8: FFFFFFFF/03D9A000 9: FFFFFFFF/0000628C
A: FFFFFFFF/00006248 B: FFFFFFFF/3B682AB8
C: 00000000/000C1238 D: 00000000/3B682B00
E: 00000000/00006288 F: 00000000/00000000
END OF SYMPTOM DUMP
--
INTERRUPT OCCURRED AT ADDRESS 800C1520
LAST KNOWN I/O OR CALL OCCURRED AT ADDRESS 00B3B0F0 AT OFFSET +0000F0 IN MODULE CASESSIS
THE Z/OS BREAKING EVENT ADDRESS IS 00000000 01611912 IN UNKNOWN PROGRAM
--
There may be an issue when trying to write within the CAIPRINT repository, please check the following to confirm:
https://support.ca.com/us/knowledge-base-articles.TEC1754252.html
The system abend of the started tasks is most probably a side effect (OEO reason 28) — this may not fix the issue.
3. ACTUAL: The Agent will activate the extended console, it ACTIVATES an extended console, it say successful, but a second later, when the Agent “inactivates” the event console the agent dies.
The OS390 agent is using access registers without initializing them. We run with a list for DIAG traps successed by IBM to catch coding errors and need this corrected so we can pass out this agent to our systems.
EXPECTED: The Agent stays active
This console is only open if the 'defultJobClass' is not set wihin the INIfile of the agent.
Just set within the '(WLM)' section this parameter:
f.ex.:
(WLM)
defultJobClass=C
If this is set the function is scipped ($d intrdr,c) – this did not resolve the issue.
Environment
For this error, the following information is useful:
Capture of the abend
JES log
Agent log
Agent trace (TCP/IP=9)
Capture of the abend
JES log
Agent log
Agent trace (TCP/IP=9)
Resolution
Workaround:None available.
Resolution: Update to at least 12.0.2 Automation Engine/Components, but the latest release of 12.0.x or 12.2.x is recommended.
Resolution: Update to at least 12.0.2 Automation Engine/Components, but the latest release of 12.0.x or 12.2.x is recommended.
Additional Information
Feedback
Yes
No
Powered by
